TEAM TRACK : FOR ALL MODELRAILROADERS Index du Forum

TEAM TRACK : FOR ALL MODELRAILROADERS
LE N: 1/160, LE HO: 1/87, LE O: 1/48 ainsi que les voies étroites qui découlent de ces échelles

 FAQFAQ   RechercherRechercher   MembresMembres   GroupesGroupes   S’enregistrerS’enregistrer 
 ProfilProfil   Se connecter pour vérifier ses messages privésSe connecter pour vérifier ses messages privés   ConnexionConnexion 

Flywheel

 
Poster un nouveau sujet   Ce sujet est verrouillé; vous ne pouvez pas éditer les messages ou faire de réponses.    TEAM TRACK : FOR ALL MODELRAILROADERS Index du Forum -> RULES & INFOS -> TUTORIAL
Sujet précédent :: Sujet suivant  
Auteur Message
eTraxx
Member
Member

Hors ligne

Inscrit le: 04 Mar 2011
Messages: 35
Localisation: South Carolina, USA
Masculin

MessagePosté le: Jeu 10 Mar - 14:20 (2011)    Sujet du message: Flywheel Répondre en citant

I needed a flywheel. The problem was that it needed to be 3/4" dia (that's 3ft in O scale) .. and for the life of me .. I couldn't find anything. I finally got a set of old HO locomotive drivers from my buddy Gary. They were a brass tire with a plastic center pressed in. I popped the rim off .. filed the flange off and I ended up with a ring that measured .750"x.110". That scaled to 3ft x 5-1/4" in O scale. Great. The only problem was that there was knurling on the inner surface of the ring. I fixed that by super-gluing a strip of .020" styrene over the knurling. That accomplished two things .. 1) Hid the knurling and 2) supplied a place for the styrene arms to adhere to.

So. Here's a SBS on how I made the flywheel.

First thing I did was draw the center of my flywheel in Sketchup. In the drawing below I drew a circle .640" dia. That's the inside measurement of the rim (with the styrene strip). I made the arms from .022" x .066" styrene strip so I drew these in. The hub I made from 1.8" tubing .. drew that .. and finally indicated the 3/16" dia reinforcing ring.


Here's all the bits cut out. You can see the brass tire with the styrene strip cemented on the inside. Evergreen styrene tubing telescopes - odd numbered sizes of round tubing telescope into next odd numbered size. Even numbered sizes of round tubing telescope into the next even numbered size. That's why I used the 3/16" tubing. I cut these .020" wide. They will reinforce where the arms cement to the 1/8" hub. The 1/8" hub is in two parts .. one is .125" long and one .145" long. Finally, the .022" x .066" strips.


Moving the camera back a bit and you can see the set-up. I glued the Sketchup printout to my marble work surface (nice and flat). I used the glue stick to do that.


I first used the school glue-stick again and glued the 1/8" x .145" hub to the center of the drawing. I used this length simply because I wanted the hub to stick out 1/8" on either side of the flywheel. The .140" is simply that 1/8" + the thickness of the arms. The strips of styrene that make up the arms are simply glued to the 1/8" hub. A small round-file stroked across the ends makes them fit. I used the Tenax for cement. Let that set up a few minutes and dropped the 3/16" ring over the hub and cemented everything well.



I used a razor-blade to snip off the arms even with that .640" circle on the paper and then when it had dried, popped it all loose. Flipping the center over I added the other 1/8" tubing (.125" long) centered on the assembly and then dropped the other 3/16" ring over the hub and snuggled up against the arms and cemented everything well.


A slight filing of the arms and the assembly fit into the ring. I again used the Tenax to cement everything. I got it close .. centered one arm by eye .. cemented that .. flipped to the opposite side .. centered THAT arm to the ring .. and continued until the center was cemented to the ring. With that dry I came back with my super-glue and my hand-dandy applicator and reinforced each joint. This makes a small fillet which is fine with me.


Finished flywheel ..


One thing I need to do is make the rim of the flywheel look polished. I think some Rub-n-Buff might work.
_________________
Edward Traxler
Revenir en haut
Visiter le site web du posteur
Publicité






MessagePosté le: Jeu 10 Mar - 14:20 (2011)    Sujet du message: Publicité

PublicitéSupprimer les publicités ?
Revenir en haut
Montrer les messages depuis:   
Poster un nouveau sujet   Ce sujet est verrouillé; vous ne pouvez pas éditer les messages ou faire de réponses.    TEAM TRACK : FOR ALL MODELRAILROADERS Index du Forum -> RULES & INFOS -> TUTORIAL Toutes les heures sont au format GMT + 1 Heure
Page 1 sur 1

 
Sauter vers:  

Index | Creer un forum | Forum gratuit d’entraide | Annuaire des forums gratuits | Signaler une violation | Conditions générales d'utilisation
Powered by phpBB © 2001, 2005 phpBB Group
Traduction par : phpBB-fr.com